膠輪壓路機施工效率高，壓實效果好，得到了工程行業用戶的好評，該設備在使用上有許多與振動壓路機等工程機械不同的注意事項，在這里我們談一談膠輪壓路機輪胎的保養。

The rubber tyred roller has high construction efficiency and good compaction effect, which has been highly praised by users in the engineering industry. There are many precautions different from vibratory roller and other construction machinery in the use of this equipment. Here we talk about the maintenance of rubber tyred roller tires.

我們要知道膠輪壓路機常配的輪胎分為充氣輪胎和實心輪胎，者兩種輪胎使用上有所不同，通常情況下，膠輪壓路機沖擊壓實輪會配備充氣輪胎，這是應為，膠輪壓路機的四個膠輪輪胎不單單起著短途運輸轉場的作用，在施工過程中，這四個輪胎還起著減震的作用。

We need to know that the tires often equipped with rubber tyred rollers are divided into pneumatic tires and solid tires, which are different in use. Generally, the impact compaction wheels of rubber tyred rollers will be equipped with pneumatic tires. This is because the four rubber tyred tires of rubber tyred rollers not only play the role of short-distance transportation transfer, but also play the role of shock absorption during construction.

膠輪壓路機的四個膠輪輪胎在施工過程中一蹦一跳，對膠輪壓路機機架上的橡膠減震有一定的保護作用，許多用戶在充氣輪胎泄氣或是被扎爛后不及時處理，就會發現機架上的橡膠減震套也會很快受損，進而有引發出其他問題。

The four rubber tires of the rubber tyred roller jump and jump during the construction process, which has a certain protective effect on the rubber damping on the frame of the rubber tyred roller. Many users do not deal with it in time after the pneumatic tire is deflated or punctured, and they will find that the rubber damping sleeve on the frame will also be damaged soon, which will lead to other problems.

充氣輪胎適合大部分沖擊碾壓施工環境，但遇到?jīng)_擊碾壓石方或是建筑垃圾時，石方或建筑垃圾的尖銳角料、以及建筑垃圾中的鋼筋等物質，很容易把輪胎扎爛，這時，好換上不怕扎的實心輪胎。

Pneumatic tires are suitable for most impact rolling construction environments, but when encountering impact rolling stone or construction waste, the sharp corner materials of stone or construction waste, as well as the reinforcement in construction waste, are easy to puncture the tires. At this time, it is good to replace them with solid tires that are not afraid of puncture.

冷再生機租賃廠家認為實心輪胎非常好用，但它會大大削弱輪胎的減震效果，降低了對機架緩沖的保護作用，而且，實心輪胎在碰到尖銳角料時或是強轉彎扭力大時，也會掰掉塊兒。

The rental manufacturer of the cold regenerator thinks that the solid tire is very easy to use, but it will greatly weaken the shock absorption effect of the tire and reduce the protective effect on the buffer of the frame. In addition, the solid tire will also break off when it encounters sharp corners or strong turning torque.

膠輪壓路機由于承載量大，且輪胎跨度小太居中，急轉彎時會受到很大的扭力，很容易損傷，因此，膠輪壓路機在轉彎時一定要慢行，盡量多調整加大轉彎半徑，同時，膠輪壓路機載重量大，充氣輪胎氣壓應保持在0.6~0.8Mpa左右，還要注意短途轉場行駛距離不易一次性過大，一般要求大約3左右進行一次輪胎降溫，否則很有可能會造成爆胎或橡膠過熱軟化。

Due to its large bearing capacity, small and medium tire span, the rubber tyred roller will suffer great torsion when turning sharply, which is easy to be damaged. Therefore, the rubber tyred roller must slow down when turning, and adjust as much as possible to increase the turning radius. At the same time, the rubber tyred roller has a large airborne weight, and the air pressure of the inflated tire should be maintained at about 0.6~0.8mpa. It is also important to note that the driving distance of short-distance transition is not easy to be too large at one time, Generally, it is required to cool the tire for about 3 kilometers, otherwise it is likely to cause tire burst or rubber overheating and softening.

膠輪壓路機的輪胎在施工過程中與地面的接觸點以及轉動方向是隨機的，但膠輪壓路機在施工過程中必須要遵循錯輪回轉原則及錯峰碾壓原則，因此，這種條件下膠輪壓路機的輪胎有時會“碰巧”與后橋鎖緊螺帽的鎖緊方向相反，因此，每次停車檢查各連接部分的緊固零件是否有松脫現象時，也都要看看小輪轂的鎖緊螺帽有沒松動，也不要忘記檢查輪胎氣壓，檢查軸承是否發熱，如有問題，要立即處理。

The contact point and rotation direction of the tire of the rubber tyred roller with the ground during the construction process are random, but the rubber tyred roller must follow the principle of staggered rotation and staggered peak rolling during the construction process. Therefore, under this condition, the tire of the rubber tyred roller sometimes "happens" to be opposite to the locking direction of the rear axle locking nut. Therefore, every time you stop to check whether the fastening parts of each connecting part are loose, Also check whether the locking nut of the small wheel hub is loose, and don't forget to check the tire pressure and whether the bearing is hot. If there is a problem, it should be dealt with immediately.

以上就是今天為大家介紹的關于問題以及注意事項的全部?jī)?nèi)容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站http://m.gzmilo.com，我們的工作人員會及時與您取得聯系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://m.gzmilo.com , our staff will contact you in time.