天氣清冷之前，機械該如何進行保養呢？冷再生機出租廠家這里為您簡單的講一講。

How to maintain the machinery before the cold weather? Here is a brief talk for you from the cold recycling machine rental manufacturer.

一、清洗外表

1、 Clean the surface

1.冷再生機在施工過程中會有大量的灰塵落到再生機的表面，包括施工中沾污的油跡等污染物，影響外觀事小，更為嚴重的是成為腐蝕的誘發因素。

1. During the construction of the cold regenerator, a large amount of dust will fall on the surface of the regenerator, including pollutants such as oil stains stained during the construction, which will have little impact on the appearance, and more seriously, will become a corrosion inducing factor.

1.清洗工程機械的柴油機、底盤、工作裝置的外表,除垢、除油保持再生機的外觀整潔。

1. Clean the appearance of the diesel engine, chassis and working device of the construction machinery, remove dirt and oil, and keep the appearance of the regenerator clean.

2.清洗時嚴禁用高壓、高溫的水槍來沖洗防水要求較高的部位（特別是電器部分），以免造成電器部分的損壞。

2. It is forbidden to use high-pressure and high-temperature water gun to wash parts with high waterproof requirements (especially electrical parts) during cleaning, so as to avoid damage to electrical parts.

二、保養轉子及其罩殼和滑靴

2、 Maintain the rotor and its casing and slippers

1.檢查轉子是否有水泥結垢等，及時清理灰塵，對需要割除、焊接的刀具及時更換；

1. Check whether there is cement scaling on the rotor, clean up the dust in time, and replace the cutters that need to be cut and welded in time;

2.清理轉子罩殼上的灰塵，并在施工結束收車時將轉子罩殼墊起地面5-10公分，防止雨雪的浸蝕；

2. Clean the dust on the rotor housing, and pad the rotor housing 5-10cm above the ground at the end of construction to prevent rain and snow erosion;

3.檢查滑靴，對已經磨損的滑靴部分進行補焊，螺紋處應涂抹黃油防銹。

3. Check the sliding shoes, repair the worn sliding shoes, and apply grease on the threads to prevent rust.

三、減速機油位及減速機油的檢查

3、 Inspection of reducer oil level and reducer oil

先切斷電源，等待減速機冷卻后打開放油螺塞，檢查油是否充滿，避免漏油，取油樣，檢查油色澤及粘度指數，如果油明顯渾濁，建議盡快更換。新減速機使用后（500-1000）小時更換新油（將內部污油沖干凈），其后每使用1500小時需要更換油一次，但是在使用過程中，仍需要檢查油的質量，若油有老化、變質情況要隨時更換。）

First cut off the power supply, wait for the reducer to cool down, open the oil drain plug, check whether the oil is full, avoid oil leakage, take an oil sample, check the oil color and viscosity index, if the oil is obviously turbid, it is recommended to replace it as soon as possible. The new reducer shall be replaced with new oil (flushing the dirty oil inside) within (500-1000) hours after use, and the oil shall be replaced every 1500 hours after use. However, the oil quality shall still be checked during use, and the oil shall be replaced at any time in case of aging and deterioration.)

天冷前的冷再生機怎么保養呢？以上就是問題的我相關解答了，您對此有什么想了解的就來我們網站http://m.gzmilo.com咨詢吧！

How to maintain the cold rebirth before cold weather? The above is my answer to the question. If you want to know anything about it, please come to our website http://m.gzmilo.com Consult!