除塵系統對于粉料撒布車而言，是一套起著非常重要作用的結構，在施工過程中起到過濾粉塵，達到排放要求的重要作用。下面冷再生機租賃廠家為您講解更多事項：

The dust removal system is a very important structure for powder spreaders, playing an important role in filtering dust and meeting environmental emission requirements during the construction process. Below, the cold regeneration machine rental manufacturer will explain more matters to you:

除塵系統位于車輛的后尾部，維護保養更換的時候需要把后方的上倉蓋打開

The dust removal system is located at the rear end of the vehicle, and during maintenance and replacement, the rear upper compartment cover needs to be opened

打開上倉蓋后便能看到除塵箱，除塵箱同樣有一個密封蓋板，維修的時候同樣要把這個蓋板打開；除塵箱邊部為除塵用氣瓶，同時連接著電磁閥，拆卸時把中間位置接頭擰開，把線路從接頭處斷開即可。

After opening the upper compartment cover, you can see the dust removal box, which also has a sealed cover plate. When repairing, it is also necessary to open this cover plate; The edge of the dust removal box is a gas cylinder for dust removal, which is connected to an electromagnetic valve. When disassembling, unscrew the middle position connector and disconnect the circuit from the connector.

打開蓋板后可看到內部的除塵結構，內部除塵布袋由上部花板加裝螺栓緊固，拆卸時應將全部花板及固定螺栓拆除。

After opening the cover plate, the internal dust removal structure can be seen. The internal dust removal bag is fastened by adding bolts to the upper flower board. When disassembling, all flower boards and fixing bolts should be removed.

目前除塵布袋有兩種，一種為布料式，一種為折疊式。

There are currently two types of dust removal bags, one is fabric type and the other is foldable type.

布料式內部含有一個金屬內撐，拆卸時應將內部金屬內撐一起拆卸下來，拿出來后將除塵布袋與金屬內撐分離；分離后檢查下除塵布袋內部有無粉料，如有則需清理出來，用氣槍對除塵布袋自內向外進行反復吹掃，同時檢查除塵內撐有無破損、變形情況，如有，應及時修復處理。

The fabric type contains a metal inner support inside, which should be removed together during disassembly. After taking it out, the dust removal bag should be separated from the metal inner support; After separation, check if there is any powder inside the dust removal bag. If there is any, it needs to be cleaned out. Use an air gun to repeatedly blow the dust removal bag from inside to outside, and check if there is any damage or deformation in the dust removal support. If there is any, it should be repaired and treated in a timely manner.

折疊式除塵布袋無內撐，可直接拿出，拿出后檢查下除塵布袋內部有無粉料，如有則需清理出來，同時用氣槍或毛刷自上向下對沾附在除塵布袋上的粉塵進行刷除、吹掃干凈。

The foldable dust removal bag has no internal support and can be taken out directly. After taking it out, check if there is any powder inside the dust removal bag. If there is any, it needs to be cleaned out. At the same time, use an air gun or brush to brush and blow away the dust adhering to the dust removal bag from top to bottom.

清理完除塵布袋后還需對除塵箱內部進行檢查，查看下內部是否有物料塊或存在開焊的情況，如有應及時處理。

After cleaning the dust removal bag, it is also necessary to inspect the inside of the dust removal box to see if there are any material blocks or open welds inside. If there are any, they should be dealt with in a timely manner.

除塵布袋清理干凈后按照原來的裝配方式進行重新裝配，裝配時一定要注意除塵布袋與內部裝配板的密封性，不要留任何的縫隙，將緊固螺栓緊固到位。

After cleaning the dust removal bag, reassemble it according to the original assembly method. During assembly, be sure to pay attention to the sealing between the dust removal bag and the internal assembly plate, do not leave any gaps, and tighten the fastening bolts in place.

緊固除塵箱蓋板時注意下有無變形的地方，如有及時加裝密封膠墊，避免后期漏氣。同時，檢查下氣瓶，查看下內部是否有水份，如有及時倒出。

When tightening the cover plate of the dust removal box, pay attention to any deformation. If there are any, add a sealant pad in a timely manner to avoid air leakage in the later stage. At the same time, check the gas cylinder to see if there is any water inside, and if so, pour it out in a timely manner.

接除塵電磁閥的時候注意下電磁閥的接線方式，接好線后應進行使用測試，使用測試無問題后再將后倉蓋進行封蓋處理，螺栓緊固到位后應在接縫位置涂抹密封膠進行后的密封處理。

When connecting the dust removal solenoid valve, pay attention to the wiring method of the solenoid valve. After connecting the wires, conduct a usage test. If there are no problems during the usage test, seal the rear compartment cover. After the bolts are tightened in place, apply sealant to the joint position for subsequent sealing treatment.

無論是哪一種除塵布袋都有一定的使用壽命，一定要定期更換，否則因小失大，引起嚴重的車輛損壞就得不償失了。還有什么事項就來我們網站http://m.gzmilo.com咨詢吧！

No matter which type of dust removal bag it is, it has a certain service life and must be replaced regularly. Otherwise, serious vehicle damage caused by small losses will not be worth the loss. If there are any other matters, please come to our website http://m.gzmilo.com Consult!