冷再生機保養的內容主要是清潔、緊固、調整、潤滑、防腐。為了讓大家更好的去使用，下面冷再生機出租廠家為您分析：

The maintenance of the cold regeneration machine mainly includes cleaning, tightening, adjustment, lubrication, and anti-corrosion. In order to help everyone better use it, the rental manufacturer of the cold regeneration machine will analyze for you:

例行保養以清潔、潤滑、檢查和緊固為中心，在每班出車前、工作中及收車后都要按要求進行例行保養。根據冷再生機設備的保養要求，在達到規定的工作小時或規定的里程后，必須進行相應的定期保養，包括以下內容:

Routine maintenance focuses on cleaning, lubrication, inspection, and tightening, and must be carried out as required before, during, and after each shift. According to the maintenance requirements of the cold regeneration machine equipment, after reaching the specified working hours or mileage, corresponding regular maintenance must be carried out, including the following contents:

工作內容是潤滑、緊固并檢查各有關部位以及清潔“三濾”工作(即清潔空氣、機油、燃油濾清器等)。

The key work content is lubrication, tightening, and inspection of all relevant parts, as well as cleaning the "three filters" (i.e. cleaning air, oil, fuel filters, etc.).

以檢查、調整為具體要檢查發動機、離合器、變速器、傳動機構、轉向和制動機構、工作裝置、液壓系統以及電氣系統等工作情況并進行必要的調整，排除所發現的故障,保障機械各總成、零部件具有良好的工作性能。

Focusing on inspection and adjustment, it is necessary to inspect the working conditions of the engine, clutch, transmission, transmission mechanism, steering and braking mechanism, working device, hydraulic system, and electrical system, and make necessary adjustments to eliminate any faults found and ensure that all mechanical assemblies and components have good working performance.

是檢測、調整、排除故障隱患及平衡各部機件的磨損程度。要對影響使用性能的部位及有故障征兆的部位進行診斷檢查、狀態性檢測，進而完成必要的更換、調整及故障排除等工作。

The key is to detect, adjust, eliminate potential faults, and balance the wear level of each component. Diagnostic checks, status checks, and necessary replacements, adjustments, and troubleshooting should be carried out on parts that affect the performance of the equipment and those with signs of failure.

新機或大修后的冷再生機在走合期內必須進行走合保養。機械在規定的走合期內使用時，需按相應規程逐級遞增負載及轉速，并檢查潤滑、緊固情況，觀察整機各部狀況，發現異常及時解決。走合保養的是更換各部潤滑油、潤滑各部位、緊固各螺栓。

During the running in period, maintenance must be carried out for new or overhauled cold air engines. When the machinery is used within the specified running in period, it is necessary to gradually increase the load and speed according to the corresponding regulations, and comprehensively check the lubrication and fastening conditions. Observe the condition of all parts of the machine, and promptly solve any abnormalities found. The key to running in maintenance is to replace the lubricating oil of each part, lubricate each part, and tighten each bolt.

冷再生機每年入夏或入冬前應進行一次換季保養。是燃潤系統、液壓系統、冷卻系統和啟動系統等部分。需根據實際情況做好以下工作:更換燃潤油料及液壓油、調整蓄電池電解液的相對密度、采取防寒或降溫措施及清洗冷卻系統等。

The cold regeneration machine should undergo seasonal maintenance once a year before entering summer or winter. The focus is on the fuel lubrication system, hydraulic system, cooling system, and starting system. The following work needs to be done according to the actual situation: replacing fuel and hydraulic oil, adjusting the relative density of battery electrolyte, taking cold or cooling measures, and cleaning the cooling system.

在機械設備因季節因素(如冬休期)等需要停用一段時間時應進行停用保養。主要做好清潔、整容、配套、防腐等工作。更多相關事項就來我們網站http://m.gzmilo.com咨詢！

When mechanical equipment needs to be discontinued for a period of time due to seasonal factors (such as winter break), maintenance should be carried out. Mainly responsible for cleaning, cosmetic surgery, matching, anti-corrosion and other work. For more related matters, come to our website http://m.gzmilo.com consulting service