為了降低路面銑刨機的使用成本，在平時的施工過程中，要綜合考慮科學使用和維護保養兩個方面，做好以下幾方面的工作。

In order to reduce the use cost of pavement milling machine, in the ordinary construction process, it is necessary to comprehensively consider the scientific use and maintenance, and do a good job in the following aspects.

合理使用刀具

Rational use of cutting tools

銑削深度越大，刀具與材料接觸的時間越長，產生的摩擦熱就越多。為了避免刀具硬質合金頭的熱腐蝕，需要增加冷卻頭的噴水量；當銑削深度較淺（6厘米以下）時，應減少冷卻頭的噴水量，以利于材料的輸出，從而防止切削和銑削材料的接觸，減少刀具的磨損。每運行6-8小時，檢查刀具的轉動和磨損情況，確保安裝的刀具在刀架內自由轉動。

The greater the milling depth, the longer the tool and material contact time, the more friction heat will be generated. In order to avoid the hot corrosion of the cemented carbide head of the cutting tool, it is necessary to increase the water spray amount of the cooling head; When the milling depth is shallow (less than 6cm), the water spray volume of the cooling head shall be reduced to facilitate the output of materials, so as to prevent the contact between cutting and milling materials and reduce the wear of cutting tools. Every 6-8 hours of operation, check the rotation and wear of the tool to ensure that the installed tool rotates freely in the tool holder.

合理的匹配速度

Reasonable matching speed

路面銑刨機的工作轉速和轉子轉速也是該機的主要技術性能參數。工作速度直接影響機器的工作效率。由于受路面材料種類、瀝青混合料強度、銑刨深度和環境溫度的影響，工作速度一般設計為無級調節，以滿足上述工況變化的要求。

The working speed and rotor speed of the pavement milling machine are also the main technical performance parameters of the machine. The working speed directly affects the working efficiency of the machine. Due to the influence of pavement material type, asphalt mixture strength, milling depth and ambient temperature, the working speed is generally designed as stepless adjustment to meet the requirements of the above working conditions.

保護腰帶

Protective belt

為防止物料松動造成皮帶磨損，保證轉子空間的密封，限制磨碎舊料的粒度，同時保證皮帶接收和皮帶不受額外顛簸的可靠性，可以使用。采用皮帶靴和分級控制梁。定期檢查和更換皮帶靴，采用合理的分級控制方案，可以充分保護皮帶，減少皮帶磨損，形成可靠穩定的收料機構。

It can be used to prevent belt wear caused by loose materials, ensure the sealing of rotor space, limit the particle size of grinded old materials, and ensure the reliability of belt receiving and belt free from additional bumps. Belt shoes and graded control beams are used. Regular inspection and replacement of belt boots, and the adoption of a reasonable hierarchical control scheme can fully protect the belt, reduce belt wear, and form a reliable and stable receiving mechanism.

定期清潔

Regular cleaning

冷再生機租賃廠家認為每個系統的清潔度對機器的可靠性非常重要。一些污垢和尖銳的固體顆粒被帶入系統，隨時可能發生摩擦、堵塞、卡住等故障，甚導致密封泄漏和損壞。溫度升高，造成一系列惡性循環。

The rental manufacturer of cold regeneration machine thinks that the cleanliness of each system is very important to the reliability of the machine. Some dirt and sharp solid particles are brought into the system, which may cause friction, blockage, jamming and other failures at any time, and even lead to seal leakage and damage. The rising temperature causes a series of vicious cycles.

銑刨機未來會得到越來越廣泛的應用，遵守操作規則，注重對銑刨機的科學使用、合理保養，讓設備發揮大功效，對提高施工質量和效率，降低施工成本有著重要的意義，更多內容就來網站m.gzmilo.com關注了解吧！

The milling machine will be more and more widely used in the future. Following the operating rules, paying attention to the scientific use and reasonable maintenance of the milling machine, and making the equipment work effectively are of great significance to improve the construction quality and efficiency and reduce the construction cost. For more information, please visit www.tclqgc Com follow and understand!